These Mercedes Benz Style LED Daytime Running Light comes with a screw bracket for you to hold the lights on any location of your bumper.  With 6 Hi-Power LED, this daytime running light gives your car a super bright Mercedes Benz look in the dark as well as day time.    It is a perfect add on if you have a Mercedes and want to have the newest trendy look, or if you want to give your vehicle a more outstanding appearance in the dark.

Before the aftermarket G35 fog lights come out to the market, if you want to install fog lights for your G35, you have to either change the whole front body kit to the Kenstyle body kit with the fog lights hole or you will have to cut a hole for your lower grille and wire the fog lights.  Both DIY steps are very complicated and cannot be modified easily.  With the newest aftermarket 03-07 Infinit G35 Coupe fog lights kit, the problems are solved.  Basically, our G35 fog lights come with the mounting brackets to replace the whole lower grille of your G35, and all wiring and harness are pre-assembled; therefore, you can install these G35 fog lights with ease.  Moreover, our G35 fog lights are using H3 light bulbs, and you can upgrade these G35 fog lights with H3 HID Conversion Kit.  Turbometal carries 3000K JDM Yellow HID, 6000K Pure White HID, 8000K Blueish White HID, 10000K Pure Blue HID and 12000K Purple HID.  Moreover, our G35 fog lights come with clear lens and yellow lens, so G35 drivers can have more option to match the color of their vehicle.  The clear lens G35 fog lights can apply different color temperate of HID and match the output of your G35 fog lights.  On the other hand, the yellow lens G35 fog lights can only apply the 3000K yellow HID, but it does give your G35 a very sporty JDM look!

6 High-Intensity LED Off Road Light – Universal

8 High-Intensity LED Off Road Light – Universal

14 High-Intensity LED Off Road Light – Universal

The Chevy Avalanche is a sport utility truck that has an open bed that opens to the back seat area with a folding panel.  The Avalanche is a great truck that was made for off-road challenges.  Off-road trips are more than just a hobby, off-road trips can be lots of enjoyable fun but also dangerous.  The number main concern when you take your Chevy Avalanche off-road you want to make sure you can see where you’re going.  Turbo Metal carrys the new Chevy Avalanche 4×4 off-road fog lights with a build in 6000K hid system. These built in hid off road lights can be installed on the Chevy Avalanche, fast and easy.

The Chevy Avalanche off-road fog light has a diameter of 5.5″ inches with a removable front shield guard.  These Chevy Avalanche off-road fog lights can be mounted on grills or bull bars or any where else you can think of for mouting.  The built in 6000K Hid System in the fog lights can help produce 5 times brighter light output.  Since the hid system is already built into the fog lights there is no need for messy wiring.  The hid fog light kit for the Avalanche also comes with wiring and a switch.  The back housing of the Chevy Avalanche fog lights are made of metal to endure the toughest off-road driving conditions.  The front plastic guards of the Chevy Avalanche hid fog lights are able to be removed.  With these new hid fog lights keeping the road bright you’ll have nothing to worry about when you go on your off-road drives.

Lexus IS300 OEM Style Fog Lights Replacement

Lexus IS300 Clear Fog Lights

Lexus IS300 JDM Yellow Fog Lights

Lexus IS300 JDM Smoke Fog Lights

These Lexus IS300 Fog Lights are with OEM quality and directly replacing your stock IS300 fog lights.  If you just want to replace your old stock fog lights with the same style of IS300 fog lights, you can get our IS300 OEM style fog lights replacement.  If you want to give your IS300 a different look, try to get the clear lens IS300 fog lights and give your Altezza a clean fog lights look.  You can also try the most popular JDM look Yellow IS300 fog lights which gives your Lexus IS a very aggressive JDM racing look.  If you want a black out look on your IS300, the Lexus IS300 smoke fog lights will definitely be your choice.

These IS300 fog lights are using 9006 light bulbs, and you can also upgrade the light source to 9006 HID conversion kit.  Turbometal carries 9006 HID conversion kit in 6000K pure white, 8000K blueish white, 10000K pure blue and 12000K purple.  You can pick the color you want to match your IS300 with a super bright fog lights output.

Notice that these 09-10 Honda Civic fog lights will ONLY fit 2009-2010 Honda  Civic 4 Door Sedan, and it WILL NOT FIT 09-10 Honda Civic 2 door coupe.  These 09-10 Honda Civic fog lights come with all necessary parts for installation including the on/off switch.  These Civic fog lights also come with pre-installed H11 light bulbs, but as mentioned, it will be a good idea to apply HID conversion kit with these fog lights kit.  A little bit of modification will be needed to do the back cover of the fog lights if you are going to install HID kit.  Basically, there is a fog lights cover at the back of the fog lights that protect the housing of the fog lights and cover the back of the fog lights.  With the HID conversion kit, you will need to drill a little hole at the back cover to allow the wires to come out from the HID light bulbs, or you can cut a little hole to allow the wires out.

As we mentioned before, it is a good idea to apply HID conversion kit with these 03-04 Toyota Corolla fog lights.  If you are applying HID with clear lens Corolla fog lights, you can apply H3 3000K Yellow HID kit, H3 6000K pure white HID kit, H3 8000K blueish white HID kit, H3 10000K pure blue HID kit or H3 12000K purple HID kit.  On the other hand, if you are installing yellow lens Corolla fog lights, you can applyH3 3000K Yellow HID kit only because the lens will only allow yellow light output to go through.

If you are still reading this page, you may be already interested in the following item that makes your Toyota Tacoma off road driving even better:

Did you purchase this item and have it installed on your vehicle? Do you want to share with other shoppers? We are offering 5% rebate for providing your installed pictures.

Jeep TJ Wrangler is also one of the choices for Off Road adventure. As you see off road drivers love to add fog lights on their vehicle for better visibility in wild. TurboMetal store also carries such off road fog light which also has Xenon HID light bulbs addon. This will boost your wild adverture brightness to a much higher level.

If you’ve purchased this Off road fog light and want to share your pictures, please email us and we’ll offer you 5% rebate back.

If you have a Toyota FJ Cruiser, then you may be interested in the following product. TurboMetal would like to introduce our Toyota FJ Cruiser 4×4 Off Road Fog Lights with Build In 6000K HID.

The build in 6000K HID will definitely maximize the brightness of your Toyota FJ Curiser. These fog lights/driving lights are made with strong metal which is also dirt and water proof.  This fog lights/driving lights also come with the removable cover which you can remove them easily for clean up.

Please feel free to visit our TurboMetal storefront for the product detail, you are also encouraged to contact us via our toll free number during business hour as our sale representative would love to tell you more about this item.  Now, let’s take a look in the following gallery which show the Toyota FJ Cuiser with 4×4 Off-Road Fog lights/Driving lights installed:

The H2 Hummer was built for hardcore out door fun.  When you’re going to take your H2 Hummer off-road make sure you’re equipped with off-road fog lights.   The number one concern when you take your H2 off-road you want to make sure you can see where you’re going.  Turbo Metal would like to introduce our 2010 Hummer H2 4×4 off-road fog lights with a build in 6000K hid system.  The fog light has a diameter of 5.5″ inches with a removable front shield guard.   The unit can be mounted on grill guards, bull bars, or on top of roof racks.  The built in 6000K Hid System in the fog lights can help produce 3-4 times brighter light output.  Since the hid system is already built into the fog lights there is no need for messy wiring.  The back housing of the H2 fog lights are made of metal to endure the toughest off-road driving conditions.  Check of some of the installed pictures below.

Acura RSX CCFL Halo Projector Headlights:

Acura RSX Fog Lights:

Verify the kit contents

• Left Fog Lamp ( Driver’s side ) Assembly
  -Fog Lamp
  -Fog Lamp (LH) Holder
  -9005 Lamp 42W
• Right Fog Lamp (passenger’s side)
  -Fog Lamp
  -Fog Lamp (RH) Holder
  -9005 Lamp 42w

• Fog Lamp Switch (dashboard mounting)
• Harness Assembly
  -Fog Lamp Switch Harness
• Fog Lamp Switch Harness

1: Lossen the bottom of the Splash Shield

See Figure 1: Remove both of the 10mm bolts from the Spiash Shield behind the left (driver’s side) Fog Lamp position.  Use either a 10mm socket or a Phillips screw driver.

See Figure 2: Remove the lower Push Clip from the Spiash Shield.  Push in both wings, with a flat bladed screwdriver, to remove it the Weather Guard from bumper.

2: Remove the Fog Lamp Blanks from the bumper

Insert a thin, Flat screwdriver, at about 12 and 9 o’clock, to release the tab.  Pull the Filler out from the front.  (See Figure 3)

3: Install the Left Fog Lamp ( driver’s side ) assembly.

See Figure 4.  Put it in from the front.  Insert the two tabs, further to the back, before the one first released when removing the Filler.  Push it in firmly until you hear a Locking Sound.

Use a Zip Tie to fasten the Fog Lamp Assembly to the bumper frame as shown.
Plug the connector into the Lamp.  The connector is taped up to the harness, just above the Fog Lamp.

Install the Fog Relay

2) Remove the Fuse Box Cover.
It is located just behind the battery in the Engine bay

3) Install the Fog Relay.
Plug the Fog Relay into the position shown.  You can check the position on the Diagram located inside, under the Fuse Box cover.

Install the Fog Lamp Switch

1.) Remove the driver’s side Door Sill Molding.

2.) Remove the driver’s side Kick Panel.
Remove the Plastic Nut above the driver’s Foot Rest.

3.) Remove the Lower Driver Side Dashboard.

Remove both of the 10mm bolts, designated 1 and 21.

Pull the bottom outward slightly, then pull the top tabs out.  There are two tabs on each side of the steering wheel.  Gently, allow it to hang from the cables.

4.) Insert the Fog Lamp Switch.

Remove the Blank from the Fog Light Switch position.  Squeeze the tabs together, from the rear, and slide it out the front.

5. Install the Harness ( Disconnect the Negative of the Battery)

a) Red Wire : Positive Input to the Switch.  Located Top Left Panel 3 Pins Down from the Top.

Install the Red input Wire and connect it to the green wire, as shown.  Snap it closed with a pair of pliers.  Insert the terminal securely.

*If you have a Alarm Installed.  Please connect the Red and “the Existing White Wire” to the Green wire.
See Figure 11

When the Battery is Connected, Use the Circuit light tester on the Green Wire to verify that it’s the Parking Light Output.

b) Blue Wire: Negative Output.  Located on Top Right Panel 4 pin Down.

Install the Blue output wire tap into 22 gauge thin Blue wire, you may Unplug this Harness to make it easier to tap into, the Blue wire is thin to make sure you have a good Connection.  (See Photo Above)

c) Black Wire : Ground.

Remove the 10mm Ground Bolt Label “C”.  Place the Black wire terminal on the bolt and then replace it.  Tighten it securely.

Route the wires neatly so that they do not interfere with the panels when replaced.  Zip Tie them in place if necessary.

Place Double Check to make sure the Red and Blue wire is correct in Figure 10

6.) Restore Power  ***( Use Circuit Light Tester on Green Wire to Detect Parking Lamps)***
Connect Negative on Battery, Turn on Parking Lights Mode.
The new Switch will now illuminated.  Test Switch On-Off for the Fog Lamps.

Replace the interior panels.

Slide the driver’s side Kick Panel forward into place.  There are two clamps which must be engaged.
Replace the Plastic Nut removed in step 2.  Tighten firmly by hand.

Figure 10 – No Alarm (Double Check the Red and Blue wire is installed Properly) Before Re-Connecting the Battery
A) Connect Red Wire to Green Wire Pin#3
B) Connect Blue Wire Thin Blue Wire Pin #4
C) Connect Black Wire to Ground

Figure 11 – With Alarm (white wire) Connect Red, White to Green.
A) Connect Red Wire to Green Wire by tapping into the White Wire Pin#3
B) Connect Blue Wire Thin Blue Wire Pin#4
C) Connect Black Wire to Ground

Now, the installation is completed and don’t forget to visit Turbometal storefront for more info about 07-10 Toyota Tundra Fog Lights and also check out the HID Conversion Kit Upgrade for these fog lights:

Toyota Tundra Fog Lights 07-10 Clear (Free Ship to 48 Domestic States)

HID Xenon Conversion Kit 9005/HB3 3000K (Free Ship to 48 Domestic States)

These 96-98 Honda Civic EK fog lights use H3 light bulbs, and it is compatible with HID conversion kit; however, since the back of these Honda Civic fog lights are closed with a plastic cover, so you will need to drill a hole for the HID kit wire to go to the ballast.  The modification is very easy, and once you get the wire out, you will have a super bright HID conversion kit on your Honda Civic fog lights.  The clear lens 96-98 Honda Civic fog lights is the best for HID conversion kit because the clear lens allow different color to pass through, so you can apply 3000K yellow HID conversion kit, 6000K white HID conversion kit, 8000K blueish white HID conversion kit, 10000K blue HID conversion kit or 12000K purple HID conversion kit.  The yellow lens 96-98 Honda Civic Fog lights, on the other hand, can only produce yellow light output for the fog lights, and it works the best with 3000K HID conversion kit; however, the yellow lens fog lights give your Honda Civic EK a special JDM look, and it is the most popular Civic EK fog lights among the 3 styles.  If you are having a black Honda Civic EK, the smoke lens Honda Civic EK fog lights will fit your Civic the best because it will create a black sporty look on your bumper.  However, since the lens of the smoke fog lights are tinted, the light output will not be as bright as clear or yellow lens fog lights.

Classic 7’’ round headlights has never looked so good until now.  Turbometal unveiled its 7’’ round sealed beam headlights with a twist of adding LEDs into the headlight.  These 7” round led headlights can be used with any vehicle with a 7 inch headlight application.  The headlights are compatible with hid kits as well.

Installation is very simple on these 7” round led headlights.  All you need to do is remove the rubber cap on the back of the 7” led round headlights, place the bulbs in or hid bulbs in and lock it into place with the metal pins.  If you plan on using these 7” round led headlights with a hid kit, make sure when you’re putting the bulbs in they are not touching the side.  Take your time and install them the correct way or else if the bulbs touch the side of the housing, the high temperature hid bulbs will heat up the housing and cause smoke.  In the back of the 7” round led headlights there are also 2 sets of loose wires for the Led, which can be wiring into the parking lights or the headlights to be turned on.  It’s just a matter of personal preference.

04-05 Honda Civic Euro Clear Fog Lights

04-05 Honda Civic JDM Yellow Fog Lights

04-05 Honda Civic Smoke Fog Lights

These 04-05 Honda Civic Fog Lights use H11 light bulbs, and you can use H11 HID conversion kit for these fog lights to produce a brighter light output for the fog lights.  The 3000K Yellow HID Conversion Kit can produce a JDM yellow style light output for your euro fog lights, and it will be my recommendation.  If you want the fog lights to match your headlights, you can get the clear fog lights with either 6000K or 8000K HID kit depends on what color of your headlights is:

Turbometal’s LED daytime running light is universal fit all vehicles.  These daytime running lights directly connect to your battery or low beam plug, so you can decide when it will light up, where you want them to light up and how you want them to light up.  For example, I’ve seen people put these daytime running light behind their grille, and they will light up when the turn signal is on.  You can put it in the middle or side of your bumper, so the LED daytime running light will look be like the fog lights function.  The position of the daytime running lights is totally up to you, and you have the freedom to connect it to the battery ( so it will light up all the time ), to low beam ( so it will light up when your low beam is on ) or to the turn signal ( so it will light up when you turn on your turn signal light ).  Notice that we carry daytime running lights in different sizes and different features, so browse Turbometal’s daytime running lights category and find the daytime running light that fits your car the best.

01-03 Honda Civic Fog Lights – Clear

01-03 Honda Civic Fog Lights – Smoke

01-03 Honda Civic Fog Lights – JDM Yellow

Among the 3 styles 01-03 Honda Civic Fog Lights, I personally prefer the yellow lens 01-03 Honda Civic fog lights which gives your 01-03 Honda Civic a JDM look; however, the bad thing about these yellow fog lights is that they can only output yellow lights because the color of the lens limit the light output.  If you want your fog lights output other colors than yellow, you have to go with the clear housing 01-03 Honda Civic fog lights.  In my opinion, the clear lens fog lights work the best with HID conversion kit because the lens allow all the light to pass through the transparent lens, so it will have less risk for the lens to be melted.  The smoke lens fog lights, on the other hand, match the best with dark color Honda Civic; however, since these smoke lens 01-03 Honda Civic fog lights are tinted, they will trap some heat inside the housing and increase the risk of melting lens in a long drive.  Therefore, if you are using smoke lens 01-03 Honda Civic Fog lights, you should apply HID conversion kit because HID produces less heat than regular light bulbs.